Attic Insulation Contractors in Toronto, ON
Our crew looks in the attic first, then seals the attic floor, sets baffles and insulates to a depth you can read from the hatch.
We are attic insulation contractors in Toronto, working on wartime and post-war bungalows and other houses across west Toronto and York. Before we quote, one of us goes up the hatch to see what's actually there. Then we seal the attic floor, set baffles and insulate. It suits homeowners and landlords who would rather have one crew handle the attic from the first look through to the cleanup.
What an attic job covers, start to finish
We do every attic job in the same order, and the quote lists each step so you know what you're paying for. Here is how it goes:
- Look in the attic. One of us goes up the hatch with a light and a depth ruler before we quote anything.
- Note what's there: what kind of old insulation it is, how deep it lies, any wet or flattened patches, and where the soffit vents are.
- Seal the attic floor at the top plates, plumbing stacks, wiring holes, pot lights and the gap around the chimney.
- Set a baffle in each rafter bay that has a soffit vent.
- Take out old insulation if it's wet, damaged by rodents or too far gone to top up.
- Insulate to the depth written on the quote.
- Fix depth rulers to the framing so you can check the depth yourself from the hatch after we leave.
- Weatherstrip the hatch and fit an insulated hatch cover.
- Clean up. The tarps come up, the hose goes back on the truck and we vacuum the floor under the hatch.
Wartime and post-war bungalow attics
We insulate attics in wartime and post-war bungalows across west Toronto and York, the same houses where we do basement, wall and spray foam work. We plan around three things on the first visit.
Low roofs at the eaves
If your roof is low at the eaves, there may be only a hand's width between the roof deck and the top plate. That is where a baffle matters most. We reach it from inside with a long pole, or use spray foam where nothing else will fit.
A small attic hatch
If your attic hatch is a small square in a closet ceiling, everything has to come through it. Blown-in goes up a hose, so the size of the hatch doesn't matter much. Batts and baffles get passed up one at a time.
Old insulation in thin layers
Thin layers of old insulation are often a mix: loose fill from one era, fibreglass batts from another. We check each layer at the depth ruler and at the eaves before we tell you whether a top-up will do.
Sealing the attic floor
We seal the attic floor before any insulation goes in, because loose insulation slows heat down but does nothing to stop air. Warm, damp air from the house rises through gaps in the ceiling, and in winter it can leave frost on the underside of the roof deck.
Top plates and wall cavities
The top plates are the boards running along the tops of the walls. Where the ceiling drywall meets them, a crack can open straight down into the wall cavity. We seal those lines with caulk or foam.
Plumbing stacks and wiring holes
A plumbing stack comes up through the attic floor in a hole cut wider than the pipe. Wires pass through drilled top plates. We fill both kinds of hole with foam.
Pot lights and the chimney
Older pot lights in the top-floor ceiling can leak air through the housing. We cover each one with a box that keeps insulation the required distance from the fixture, then seal the box. Around the chimney we use sheet metal and fire-rated sealant, never foam.
The attic hatch
We weatherstrip the frame so it closes tight, then fit an insulated cover so it's no longer the weak spot in the attic floor.
Keeping the attic vented
An insulated attic still needs air moving through it, coming in at the soffit vents and leaving near the ridge. We set a baffle in each rafter bay that has a soffit vent. A baffle is a formed channel fastened under the roof deck. It keeps an air path open over the top plate; without it, blown-in insulation drifts into the eaves and blocks the vents.
Bathroom and kitchen fans should vent outside, not into the attic. If your fan duct stops in the attic or lies loose on the old insulation, that moist air ends up on cold wood. We point it out on the quote: running that duct to an outside vent is a job for a roofer or a ventilation contractor.
Top-up or tear-out
An attic insulation top-up works when the old insulation is dry, has no droppings in it and lies flat enough for new material to sit on. We make that call at the hatch, with the depth ruler in hand, after a look along the eaves.
Wet or rodent-damaged insulation has to come out. Wet material has lost its loft and holds water against the ceiling drywall. Rodent-damaged material is tunnelled through and full of droppings. If animals are still living up there, a pest-control company needs to deal with them, and with how they got in, before we start. Then our crew does the insulation removal and puts new insulation in.
Vermiculite is the one thing we don't touch. It's a loose, grey-brown fill that looks a bit like gravel, and some of it contains asbestos. If we find vermiculite, we stop, leave it as it is and recommend you have a qualified lab or abatement firm test it before any work goes ahead.
Blown-in, batts or spray foam in an attic
Which material makes sense depends on the attic floor, the hatch and how much room there is at the eaves.
Blown-in loose fill
Blown-in insulation is a good fit for an open attic floor. A machine outside pushes cellulose or fibreglass loose fill up a hose, and it settles around joists, wires and junction boxes without leaving gaps. We level it off to the depth rulers.
Batts
Batts work where the attic floor is clear and even, with regular joist spacing and not much in the way. Each batt has to be cut around obstacles, and a sloppy cut leaves a gap. At low eaves they're hard to place well.
Spray foam
Spray foam seals and insulates in one pass, which makes it useful in tight spots: eaves too shallow for a baffle and loose fill, a kneewall, or an attic insulated along the roofline instead of the floor. Our spray foam contractors page goes through how that work is done.
How much attic insulation is enough
SB-1 lists Toronto at 3520 heating degree-days, below the 5000 that marks Zone 1. SB-12 asks a new Zone 1 house for at least R-60 in an attic ceiling under packages A1, A2, A4 and A6, or R-50 under A3 and A5.
Those numbers are for new construction. In an existing attic they're a useful reference, not a requirement. We measure what you have, show you where new insulation would take it, and write the target depth on the quote.
Choosing an attic insulation contractor
Ask these before you sign, and get the answers on the quote:
- Will someone go up the hatch before quoting? From the driveway, nobody can see the depth, the old material or the soffit vents.
- What gets sealed before the insulation goes in? A good answer names the top plates, plumbing stacks, wiring holes, pot lights, chimney gap and hatch.
- How will I know the depth? Depth rulers fixed to the framing let you check it from the hatch after the crew has left.
- Will there be a baffle at every soffit vent? If the answer is vague, the vents may end up buried.
- What happens if you find vermiculite? Work should stop, and they should tell you to have it tested by a qualified lab or abatement firm.
- Is cleanup on the quote? Ask about tarps, the area around the hatch and any old material that comes out.
Rebates for attic work
Home Renovation Savings lists attic insulation among the rebates with no home energy assessment, so you can apply without booking one first. The programme sets its own terms and they do change, so check the current rules before work starts. Our insulation rebates page explains how the programme works.
FAQ
Common questions about attic insulation contractors
In most bungalow attics, blown-in loose fill works best. It goes up a hose through a small hatch and settles around joists and wires. Where the eaves are too low for both a baffle and loose fill, spray foam is the better choice. Batts only suit a floor that's clear and even.
Old attic insulation has to come out when it's wet, damaged by rodents or too flattened to take a top-up. Dry insulation that lies flat can usually stay, with new material on top. If the old fill turns out to be vermiculite, we stop and recommend you have it tested by a qualified lab or abatement firm before anything else happens.
Yes. One of us goes up the hatch before we give you a quote. We need to see what the old insulation is and how deep it lies, where the attic floor leaks air, and where the soffit vents are. Seeing it is what lets us give you a firm quote.
No. Insulation work, new or replacement, is on the city's no-permit list, and the Zoning Bylaw still applies to the property. If the attic job is part of a larger renovation, the other work may need a permit of its own.
Get a quote
Book an insulation quote in Toronto
Call (437) 563-1402 or send the form. We'll come and look at the space, go over the options with you and give you a firm quote.