Our crew installs blown-in insulation in Toronto attics: loose blown fibreglass or cellulose blown through a hose onto the attic floor. Before the hose goes up, we seal the attic floor and fit baffles at the eaves. We also staple depth rulers to the joists so you can see what you paid for. It's a good fit for homeowners and landlords whose open attic floor is thin, uneven or due for a top-up.

From the truck to the attic floor: how a blown-in job runs

On a blown-in job, the blowing machine stays at the truck. Only the hose comes into the house. We run it from the street through a door or window up to the attic hatch, and we lay tarps along the path and on the floor under the hatch.

One person stays at the machine feeding bags into the hopper. The other is up in the attic with the hose. They start at the far eaves and work back toward the hatch, so the hose never gets dragged across insulation that's already down. The two keep talking the whole time, and the feed stops whenever the person on the hose needs to move or check a ruler.

Once the attic floor is done, we bundle up the empty sacks, roll up the tarps and vacuum the path. The bag count is on your quote, and you're welcome to count the empties yourself before we go.

Blown fibreglass and cellulose, compared

Both fill in around joists, wiring and awkward framing far better than batts do. Where they differ is what they're made of and how they behave once they're down.

Blown fibreglass

Blown fibreglass is spun glass fibre chopped into loose fill. It's light, it doesn't take on water easily, and it settles less than cellulose. It copes better than cellulose if a small leak comes back, though the leak still gets fixed first. We also go with it when the ceiling below is old plaster and we'd rather not add weight.

Cellulose

Cellulose is recycled paper treated with a fire retardant. It packs denser than fibreglass, which helps slow air moving through the layer. It also settles more, so we blow it deeper to allow for that. We use it in dry attics with a well-sealed floor. There's more on it on our cellulose insulation page.

Adding to old insulation or starting clean

If the existing layer is dry and even, topping it up is fine. The new loose fill goes right on top, and the rulers measure the combined depth from the ceiling board up.

Wet, flattened or rodent-damaged material has to come out first. Covering it just hides the leak or the droppings, and the new layer ends up sitting on the problem. Our insulation removal crew vacuums the old fill out, and then we seal and insulate the bare floor. If animals are still getting in, you'll need a pest-control company to deal with them and close up their entry point before we start.

Vermiculite is different. It looks like loose, pebbly granules, grey-brown or gold, and it's much lighter than gravel. If we find it, we stop and leave it alone. We'd recommend having a qualified lab or abatement firm test it before any work goes ahead.

Sealed gaps and eave baffles come before any insulation

We air seal first because loose fill doesn't stop air. Warm, moist air from the house rises through gaps in the ceiling, and insulation piled over those gaps only filters it. Before the hose goes up, we seal:

  • Top plates, where the tops of interior walls meet the ceiling. We run caulk or foam along the gap.
  • Plumbing stacks and flues. Foam goes around a vent stack, and fire-rated sealant goes around a flue or chimney.
  • Wiring holes, plus the gaps around ceiling electrical boxes.
  • The hatch itself, with weatherstripping on the frame and rigid foam on the back of the cover.

Baffles keep the soffit vents open

Next, baffles go in at the eaves. A baffle is a rigid channel stapled between the rafters above the outside wall. It holds the insulation back so air from the soffit vents can still get into the attic. Without baffles, a deeper layer of loose fill spills into the eaves and blocks those vents, and the roof deck loses the airflow that keeps it dry.

If your attic needs more than sealing and baffles, our attic insulation page covers the bigger jobs.

Reading the bag chart and the depth rulers

Every bag of blown insulation has a coverage chart printed on it, and it's the simplest way to check our work. For a given floor area, the chart links the number of bags and the installed depth to an R-value. You can check the chart and the rulers yourself:

  • Find the row for the R-value on your quote. Read across to the bag count for the floor area the chart lists, then scale it to the size of your attic floor.
  • If the chart gives two depths, note both. One is the installed thickness on the day, and the other is what the layer settles to over time. When we finish, the rulers should read at least the installed figure.
  • Ask for the bag count before we start, then count the empties after. If the count comes up short of the chart for your attic, the R-value is short too.
  • Check the rulers from the hatch. They're stapled upright to joists across the attic with the depth printed on the face, so you don't have to step onto the joists to read them.
  • Look at the surface between the rulers. Low spots near the hatch or out at the far eaves mean the hose didn't cover those areas evenly.

Target levels for an attic floor in Ontario

SB-12 asks a new Zone 1 house for at least R-60 in an attic ceiling under packages A1, A2, A4 and A6, or R-50 under A3 and A5.

Toronto is in Zone 1. SB-1 puts the city at 3520 heating degree-days, below the 5000 cutoff for the zone.

In an existing attic, those levels are a guide, not a rule. A top-up on an older house doesn't have to meet new-house requirements. SB-12 still gives you a sensible number to aim for, and the coverage chart tells you how many bags it takes to get there.

What moves the price of a blown-in job

Your quote covers the prep work as well as the insulation. The main things that change the price:

  • The size of the attic and how easy it is to get into. A bigger floor takes more bags, and a small hatch or a low, cramped attic slows down the hose work.
  • How much air sealing it needs. Lots of open top plates, stacks and wire holes means more time and material before any fill goes down.
  • Baffles. Every rafter bay along the eaves gets one, so a long eave line adds up.
  • Removal. Old, wet or rodent-damaged insulation has to come out before the new fill goes in.
  • How deep you're going. A higher R-value takes more bags.
  • Which material you choose. Blown fibreglass and cellulose cost different amounts per bag.

What to expect on install day

On install day you'll see tarps laid from the door to the hatch, and the crew sealing gaps and fitting baffles before any insulation goes down. Please keep the path to the hatch clear and your pets in another room. Our install day page goes through the visit step by step, from when we arrive to the last ruler check.

The Home Renovation Savings attic rebate

Home Renovation Savings puts its attic insulation rebate in the group with no home energy assessment. Terms apply, and the programme decides its own eligibility and amounts, so check the current rules before work starts. Our insulation rebates page explains how it works. We don't do energy assessments or book them for you.

More on Blown-In Insulation

FAQ

Common questions about blown-in insulation

It depends on the area of your attic floor and the R-value you want, and the coverage chart on each bag gives the count for both. Find your target R-value on the chart, read the number of bags for the area shown, and scale that to your attic. We write the bag count on the quote so you can check it against the empties when we're done.

For a new house in Zone 1, which includes Toronto, SB-12 sets R-60 for a ceiling with attic space in packages A1, A2, A4 and A6, and R-50 in packages A3 and A5. In an existing attic those levels are a guide rather than a requirement, but they're still a sensible target for a top-up.

Yes, it settles after it goes down, and cellulose settles more than blown fibreglass. Coverage charts usually list a settled thickness next to the installed thickness, so the chart's R-value already accounts for it. We blow to the installed depth, which means the layer still hits the target after it settles.

Yes, as long as the old layer is dry, even and free of rodent damage. Anything wet, flattened or damaged by rodents has to come out first. Vermiculite is the exception. We leave it alone and recommend having a qualified lab or abatement firm test it before anything goes on top.

Get a quote

Book an insulation quote in Toronto

Call (437) 563-1402 or send the form. We'll come and look at the space, go over the options with you and give you a firm quote.

Call Text Quote