Insulation removal in Toronto means taking old, wet or rodent-damaged insulation out of an attic, wall or crawl space before new material goes in. We do it for homeowners, landlords and small commercial spaces. We run a vacuum hose from the truck, bag the old material and take it away, then air seal and re-insulate. The one thing we don't remove is vermiculite. If we find it, we stop.

When insulation has to come out

Insulation has to come out when it is wet, flattened, full of droppings or in the way of new work. A roof leak or an ice dam can soak it, and soaked insulation holds water against the ceiling and the joists. It dries slowly, if it dries at all. At the hatch, look for stains on the batts or the loose fill, or brown rings on the ceiling below.

Flattened insulation is the second case. Loose fill that has been walked on, crushed under storage boxes or matted down by a leak doesn't trap air the way it used to. Blow new material over a damp, packed layer and you've just buried the problem.

Old material also has to come out if it shows droppings, nests or tunnels, if it sits where spray foam is going, or if a renovation opens up the ceiling or walls. Foam has to bond to bare framing and sheathing, so nothing can be left in its way.

If we see mould on the rafters, roof deck or framing, the job stops there. A mould specialist deals with it first, and we insulate once the framing is clear.

Tarps, hoses and bags: removal day

On removal day we run a vacuum hose from the truck to the attic hatch and lay tarps along the path between them, over any floors and stairs the hose crosses. We tape plastic around the hatch so the dust stays in the attic instead of drifting into the hallway.

Loose fill goes down the hose and into large bags at the truck. Batts and rolls are different: the crew cuts and folds them in the attic, bags them by hand and carries them down. Every bag goes out on the truck with us, and nothing gets left at the curb.

When we're done, the attic floor is bare down to the boards. You can see the top plates, the back of the ceiling between the joists, and the wiring. It's the clearest look at the attic we'll get, so this is when we spot roof leaks, gaps around pot lights and plumbing stacks, and any wiring that needs an electrician before new insulation covers it up again.

Vermiculite: our crew stops

Vermiculite is a loose fill made of light, pebble-like granules, grey-brown or gold, often shiny and flaky. It pours like gravel but weighs far less. If your attic has it, it will be lying loose between the joists, not laid in batts.

Health Canada advises that some vermiculite insulation may contain asbestos and can be a health risk if disturbed, and that the best way to limit the risk is not to disturb it. It also advises assuming that vermiculite insulation produced before 1990 may contain some asbestos.

When we find vermiculite, we stop work, leave it as it is and close the hatch. We recommend having a qualified lab or abatement firm test it before any work goes ahead. If it has to come out, that's a job for a licensed abatement firm, not us. Once they've finished, we can come back to air seal and insulate.

Rodent-damaged insulation

Rodent-damaged insulation comes out only after the animals are gone. A pest-control company handles the mice, rats, squirrels or raccoons first, and the way they got in. Pull the insulation while animals are still living up there and the new material just becomes their next nest.

Once pest control is done, we vacuum out the droppings, the nesting and the tunnelled insulation along with the rest of the old material. It gets bagged at the truck like any other tear-out and leaves with us. The attic is left down to the boards, ready for new insulation.

Spray foam removal

We can take spray foam out when it has to come out. Usually that's foam sprayed over wiring that now needs work, foam that has pulled away from the framing, or foam in the way of a renovation. Spray foam doesn't vacuum out. The crew cuts it and scrapes it off the rafters, studs and sheathing with hand tools, then bags it.

It's slower, more hands-on work than pulling loose fill, and the framing has to be scraped clean so the next layer sits flat or bonds properly. If new foam is going back in, we spray once the surfaces are bare. Our spray foam page covers where foam suits a house and where another material makes more sense.

After the tear-out: sealing and new insulation

An empty attic is the easiest time to air seal. With the old material gone, we can get at the top plates, the gaps around pot lights and bathroom fan housings, the plumbing stack and the holes where wires pass through. We seal those spots before anything covers them again.

Then we fit baffles at the eaves to keep the new insulation clear of the soffit vents, and staple depth rulers to the joists so you can check the depth yourself from the hatch. On an open attic floor, blown-in insulation is the usual choice: cellulose or fibreglass, blown through the same kind of hose that took the old material out.

Our attic insulation contractors page goes into the second half of the job in more detail, including hatches, access and choosing a material. Removal and new insulation go on one quote, so you can see what each part costs before we start.

Why removal quotes differ from house to house

A removal quote depends on what we see at the hatch and on the route back to the truck. We look at the space first, explain your options, then give you a firm quote. These are the main things that move the price:

  • Attic size and access. A hallway hatch is easier to work through than a small closet hatch, and with a low roof pitch the crew has to crawl.
  • How much material is up there, and how deep it sits between and over the joists.
  • Droppings, nesting or wet material, which mean more bags and more care with each one.
  • How far the hose has to run from the truck to the attic, counting stairs, parking and laneway access.

Removal around tenants and opening hours

Landlords and business owners can book insulation removal around tenants and opening hours. The quote lists removal, air sealing and new insulation as separate lines. If the job opens a ceiling, we can hang and finish the drywall afterwards too, so you aren't waiting on a second trade. We cover west Toronto and York, and the full list of our insulation services is on the home page.

FAQ

Common questions about insulation removal

Yes, if it's wet, flattened, full of droppings or sitting where new spray foam has to go. Insulation in that state isn't doing much, and it can hide leaks and damage underneath. If it's dry and clean and just too thin, adding more on top may be enough. We'll tell you which case your attic is.

Yes, you can stay home while we remove insulation. The work happens in the attic and at the truck, with tarps along the hose path and plastic taped around the hatch. Keep children and pets away from the hose route, and keep doors closed on rooms near the hatch.

If we find vermiculite, our crew stops work and leaves it undisturbed. Health Canada advises that the best way to limit the risk from vermiculite that may contain asbestos is not to disturb it. We recommend having a qualified lab or abatement firm test it before any work goes ahead. If it has to come out, a licensed abatement firm removes it.

Yes, we remove spray foam when it has to come out. We cut and scrape it off the framing by hand, bag it and take it away. Once the surfaces are clean, we can re-insulate with new foam or another material.

Get a quote

Book an insulation quote in Toronto

Call (437) 563-1402 or send the form. We'll come and look at the space, go over the options with you and give you a firm quote.

Call Text Quote