Spray Foam Contractors in Toronto, ON
We spray closed-cell and open-cell foam on rim joists, block walls and unit ceilings, then hang and finish the drywall over it ourselves.
Superior Insulation Contractors of Toronto are spray foam contractors in Toronto who spray foam on rim joists, block walls and unit ceilings in houses, rentals and small commercial spaces. When the foam has cured, the same crew hangs and finishes the drywall over it, so you don't have to wait on another trade. We look at the space first, tell you which foam goes where, and give you a firm quote.
Where our crew sprays foam
Spray foam is worth what it costs where air gets in through gaps and awkward shapes that batts can't seal. In west Toronto and York we spray it in three places, and each one needs its own prep before the hose comes out.
Rim joists
The rim joist is the band of framing that sits on the foundation and closes off the ends of the floor joists. Air gets in at the sill plate and through every joist bay, and a batt pushed into the bay leaves those gaps open. We spray closed-cell foam into each bay, against the rim and over the sill joint, which seals the air and insulates in one pass. If your rim joists sit over a crawl space, that falls under our crawl space insulation work.
Block walls
Concrete block foundation walls are hollow, porous and cold, so whatever goes on them can't trap water against the masonry. We spray closed-cell foam straight onto the block face. It bonds to the wall and slows vapour moving from the warm room into the cold block. The wall has to be dry before we start. Garage block walls get the same treatment, and our garage insulation page has the details.
Unit ceilings
A unit ceiling is the ceiling between one unit and the unit or unheated space above it. Foam fills the joist bays around pipes, wiring and ducts, where batts would have to be cut to fit, and it closes the air paths between floors. Between two heated units, open-cell foam is usually enough. If the space above is cold, we use closed-cell.
Closed-cell and open-cell foam
Closed-cell foam is dense and hard, and it slows vapour. Open-cell foam is soft and spongy, and vapour passes through it. That difference decides where each one goes.
We put closed-cell foam against anything cold or damp: block walls, rim joists and ceilings over unheated space. It sets rigid, sheds water at the surface, and handles air sealing and vapour control in a single layer.
Open-cell foam is for interior ceilings and walls between heated rooms, where the goal is to fill the cavity and stop air moving. Moisture isn't the concern there. It expands more than closed-cell and fills awkward bays well. We don't put it on foundation walls, because it soaks up water.
When spray foam is the wrong call
Spray foam is the wrong choice for an open attic floor you can easily get to. Loose fill does that floor for less money, and blown-in insulation goes down to a measured depth across the whole attic, checked with a depth ruler.
Foam is also the wrong first step on a wall that lets water in. If a block wall has wet patches, efflorescence or a crack that weeps after rain, the water problem has to be fixed first. Spraying foam over a leak just hides it.
If we look at your space and foam isn't the right fit, we say so on the quote and price the option that is.
Prep and staying out while it cures
We close off the work area before the foam goes on, and it stays closed until the foam has cured. You, your family, tenants and pets stay out of it the whole time. Cure time depends on the product, and we'll tell you how long it is for ours before the day of the job.
Before spraying, we tarp the floors and cover fixtures, windows, ducts and anything else staying in the room. Spray foam sticks to whatever it lands on, so we take the masking seriously.
We ventilate the work area to the outside while we spray and while the foam cures. Our crew wears respirators and protective suits for as long as the hose is running.
Drywall over the foam
Spray foam inside the house needs drywall over it for fire protection. If the foam is left bare in a finished basement or a unit ceiling, the job isn't done.
We hang and finish the drywall once the foam has cured. First we trim any foam that has swelled past the face of the studs or joists, then we hang the board, tape, mud and sand it so it's ready for paint. Since the same crew does both, the drywall is already on your quote and there's no second trade to book.
Foam in rentals and commercial units
Landlords and business owners can book foam work around tenants and opening hours. We plan the order of the rooms so one closed-off area doesn't shut down the whole building, and we tell you which spaces have to stay empty and for how long.
In a multi-unit house the work is usually in unit ceilings under the roof. A gap in a shared wall between units is a fire-separation matter for a qualified contractor or the City, so we point it out rather than foam it. In a small shop or office it's more often block walls and the rim joist line. Either way, the foam gets covered with drywall before anyone moves back in.
Taking out old spray foam
We can remove spray foam that has to come out: foam sprayed on a wall that leaked, foam that has pulled away from the framing, or foam that's in the way of a renovation. We cut and scrape it off the framing and masonry, bag it and haul it away, and the surface is left ready for new insulation.
We also handle insulation removal for old, wet or rodent-damaged batts and loose fill. If we find vermiculite, we stop, leave it alone, and recommend you have a qualified lab or abatement firm test it before any work goes ahead.
Line items on a spray foam quote
A spray foam quote should show you what you're paying for, area by area. Ours lists the lines below, and any quote you compare it with should too:
- Each area by name (rim joists, block walls, unit ceilings, garage walls) with its measured size
- Whether each area gets closed-cell or open-cell foam, and why
- The thickness or target R-value for each area
- Prep: tarps, masking floors, fixtures and ducts, and closing off the work area
- Removal of old insulation or old foam, including bagging and disposal
- Drywall hung, taped, mudded and sanded over every area of interior foam
- Ventilation during the work, and how long the area stays closed for the product we use
- Anything not included, such as fixing a leaking wall, so you know who's handling it
Do foam jobs need a permit or qualify for a rebate?
Adding or replacing insulation doesn't need a City of Toronto building permit, though the Zoning Bylaw still applies. You do need a permit for an addition or a material alteration, like adding or removing walls, so foam work that's part of a bigger renovation may fall under that renovation's permit.
Home Renovation Savings rebates that require a home energy assessment (two or more upgrades) cover attic, wall, foundation and exposed-floor insulation, plus air sealing. Foam on block walls and rim joists may fall under the foundation insulation and air sealing upgrades; check the programme's current terms. We don't do or book the assessment, and terms apply, so read the programme rules before work starts. For our other services, go to the Superior Insulation Contractors of Toronto home page.
FAQ
Common questions about spray foam contractors
Yes, as long as the rim joist is dry and we can reach it. Closed-cell foam seals the gaps at the sill plate and the joist ends and insulates at the same time, which a cut batt can't do. If the rim is wet or rotted, it gets repaired before any foam goes on.
Yes. Spray foam inside the house needs drywall over it for fire protection. We hang and finish that drywall after the foam cures, and it's its own line on the quote.
Yes, closed-cell foam can go straight onto a block foundation wall once the wall is dry. It bonds to the block and slows vapour moving into the cold masonry. If the wall lets water in, that gets fixed first. Open-cell foam shouldn't go on a foundation wall at all.
Yes. Everyone stays out of the closed-off work area while the foam goes on and until it has cured. We'll tell you how long that takes for the product we use and which rooms are affected. You can usually keep using the rest of the house.
Get a quote
Book an insulation quote in Toronto
Call (437) 563-1402 or send the form. We'll come and look at the space, go over the options with you and give you a firm quote.